Residential & Commercial Irrigation
Residential & Commercial Irrigation
One station: At any time you can simply increase or decrease Run Time to any individual station in the host controller and that station will adjust up and down with all the rest of the stations from a new level. All stations: Use the water + and - feature …
The Pro-C is compatible with the Hunter Solar Sync. Solar Sync is a sensor system that will automatically adjust the Pro-C controller’s watering run times (based on changes in local climate condition) by using the Seasonal Adjust function. The Solar Sync …
Program your Hunter controller as specified in the Owner’s Manual. When setting station run times, enter the time that would normally be programmed during the peak summer watering season. The Solar Sync is designed to adjust all run times daily based upon …
After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …
After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …
Solar Sync Troubleshooting Guide …
The X-Core Controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module. Installing the Wireless Solar Sync Sensor Simply mount the Wireless Receiver on the controller cabinet using an available …
The ACC Controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module. Installing the Wireless Solar Sync Sensor Simply mount the Wireless Receiver using the supplied brackets to mount the Wireless …
The Wireless Solar Sync Receiver and Sensor are already paired with the same frequency for an easy installation. When installed, the wireless Receiver will automatically go into a “search” mode looking for the signal from its paired Sensor. However, it is …
The.Solar Sync is a sensor system that, when connected to a compatible Hunter controller, will automatically adjust your controller watering run times based upon changes in local climate conditions.The Solar Sync utilizes a solar and temperature sensor to …
The Solar Sync sensor is simple and easy to install and is compatible with all current Hunter AC powered controllers. The sensor should be placed in an area where it can receive full sun and rain; The Solar Sync sensor measures solar radiation and …
The Pro-C / PCC controller (with SOLAR SYNC position on dial) is programmed with the Solar Sync technology and, therefore, does not require the use of the Solar Sync module. The Solar Sync Sensor (SOLARSYNCSEN or WSSSEN) is wired directly to the “SEN” …
The I-Core now has the Solar Sync software built into the controller. New I-Core controllers with built in Solar Sync are easily identified by the new Solar Sync Settings dial position on the facepack. Because the new I-Core has built in Solar Sync …
After Solar Sync has been installed and programmed, we recommend allowing the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the sensor, …
For controllers with the Solar Sync Module installed, the Region and Water Adjustment is made on the Solar Sync Module. … For accurate measurements, the Solar Sync module needs to be programmed for the typical ET (average July ET) for your region. Press …
Connecting to the ICC The Hunter ICC controllers require the installation of the Solar Sync module as well as the Sensor. Installing the Solar Sync Module Turn off AC power to the controller before connecting the Solar Sync module to the controller. …
The ICC2 controller is programmed with Solar Sync technology and, therefore, does not require the use of the Solar Sync module. The Solar Sync Sensor (SOLARSYNCSEN or WSSSEN) is wired directly to the “SEN” terminals on the ICC2 controller. Wired Solar …
Solar Sync ET sensor can share one sensor transmitter with multiple Hunter AC controllers. To accomplish this setup, each controller would need a separate wireless Solar Sync Receiver (P/N: WSSR). Each receiver will need to communicate with the same …
Module wires not properly connected to controller terminals. Wires from the Solar Sync module to the controller have been severed. Is the Solar Sync module installed on a controller that has the SOLAR SYNC dial position? If so, remove the module. … ERR …
If the Solar Sync Seasonal Adjustment is too high or too low you may need to change the Water Adjustment feature on your controller or Solar Sync Module on older models. This will allow you to fine-tune your station Run Times to allow for more watering or …
Cause The Solar Sync sensor is not connected to the controller The Solar Sync sensor wires may have a break in them or a bad connection Solution Connect the Solar Sync to the "SEN" positions on the wiring terminal - The display will then show the Region …
If a Solar Sync sensor has been installed on the Pro-C controller then the seasonal adjust value used by the controller will be calculated from the weather data supplied by the Solar Sync sensor. If it is decided that the Solar Sync sensor will no longer …
For accurate Solar Sync measurements, the controller needs to be programmed for the average peak season ET for your region. Use the following table for choosing your region. You can use methods A, B or C to help you choose which region is best for your …
After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …