Residential & Commercial Irrigation
Residential & Commercial Irrigation
Tips for Mounting the Sensor -Choose a location such as the side of a building or post. The closer the transmitter is to the receiver, the better the reception. Do not exceed 800' (243 m). -To ensure maximum range in communication, mount the receiver …
Manual Test Spindle: Press and hold the manual test spindle to confirm the proper operation of your sensor. Vent Cap and Spindle: Used to adjust reset rate or dry out time for the sensor. Radio Antenna: Transmits a wireless signal to the receiver up to …
Wiring the Sensor to the Interface Box The red and black leads from the Flow-Clik sensor are connected to the red and black leads on the Interface Box. A minimum wire size of 18-gauge wire can be used to connect the leads from the sensor to the …
WARNING! Flow-Sync is only designed for low-voltage connection to approved irrigation controller flow terminals. do not install in high-voltage 110V or 230V circuits. Flow-Sync has two wire leads for the controller connection. These may be extended up to …
Reece Irrigation & Pools …
Quick couplers allow fast access to water while maintaining in-ground durability and vandal resistance. A quick coupler valve is a great tool to use when the rotor does not need to be turned on to irrigate a large area, and it’s only needed for spot …
When designing and installing irrigation systems, the water stream's trajectory and spray height leaving a sprinkler nozzle is important information. The chart below will show the total feet of height when using the largest nozzle for the ST-1600 model. …
The Mini-Clik is an adjustable model which can be set to deactivate the system when either 1/8”, 1/4”, 1/2”, 3/4” or 1” (3-25mm) of rain hits the sensor. … Mini-Clik - Amount of Rain to Activate …
The difference between the Mini-Clik and the Rain-Clik is that the Mini-Clik adjusts for rainfall of 1/8" to 1". As the moisture-laden disks expand, they will eventually activate a switch that interrupts the circuit from the controller to the solenoid …
The on-off-auto selector switch allows the user to control the kit to automatically actuate from an irrigation controller or manually from the switch. To install the switch, make sure it’s positioned directly below an access port in the vault’s cover set. …
After installing the on-off-auto selector switch, insert the supply tubing from the switch into the control valve. This allows you to turn the valve on and off, either manually from the switch or automatically from the controller. On the control valve, …
Using the Flow-Clik Interface Box, the sensor is calibrated by pressing the Calibrate button while the highest flow zone is operating. While the system is learning the flow, the System Status Indicator light will be yellow. After a 10 second period of …
The Flow-Clik Interface Box has a System Status indicator LED that provides information on the current status of the Flow-Clik system. RED indicates an unacceptable amount of water was flowing and the system has been shut down. (Water flow exceeded the …
This section will give you a brief overview of some of the components of the Flow-Sync system. … Impeller: Rotates when flow is occurring O-rings: Provides sealing of sensor in sensor body Wires: Black and red wires connect sensor to the ACC or I-Core …
For installation of Root Zone Watering System with existing trees, follow the steps below. … Note: To service the RZWS, use a tool to access and release the two snaps from the cap. … RZWS - Existing Tree …
The 18" and 36" Root Zone Watering Systems feature a new top design that offers improved durability. The top now consists of two pieces: a body that holds onto the tubing, and a cap to snap onto the body. To remove the cap for serviceability, use a …
For new tree or shrub installation, follow the steps below. … RZWS - New Tree or Shrub Installation …
The Air/Vacuum Relief Valve (AVR) is designed to reliably discharge air during system start-up and allow air into the line during shutdown. The valve closes even with low water pressure and reduces water hammer. It is good practice to use an AVR for all …
Yes, Hunter tubing is 17mm in diameter and therefore our fittings are compatible with all other manufacturer's 17mm tubing. … Will Hunter PLD fittings work with other manufacturer's drip …
Filter Inspection Flushing Injection Systems Winterization Repair … Inline emitters can be difficult to clean (unclog). If there is a clogged section, we recommend cutting out and replacing it with new cut HDL piece. Filter maintenance is very important …
Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … HEMT - Hunter Emitter Multi-Tool … Dripline …
Welcome to the Hunter Field Server support section. In this section, you will find help with installing, programming, running, and support links. … Field Server …
Technical assistance is available using the links provided below. Please ensure you include the unique product reference number on the back of the device. The reference number is listed on the back of the gateway and starts with "FSE" followed by the …
From the Account Settings menu on this screen, you can choose where notifications will be sent if there is more than one account user and generate an API key for home automation purposes. Learn more … Sign in to your Hydrawise account. Click the ( ) …