Residential & Commercial Irrigation
Residential & Commercial Irrigation
The X-Core controller will not water manually or automatically with the dial in the system off position. Valves currently watering will be shut off after the dial is turned to the system off position. The display will flash OFF for two seconds then …
Choose from the links below for troubleshooting your X-Core controller. Station Repeats No Display SP Err ERR with Station # No AC Umbrella Icon Rain Sensor will not Shut Off System Controller does not have a start time for each station. Flashing …
The "NO AC" display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. … Check the power source by plugging a lamp or radio into the wall outlet …
The X-Core allows the user a simplified method for running a test program. This feature will operate each station in numerical sequence, from the lowest to the highest. … After a 2 second pause, the test program will start. The display will show the …
If the controller display shows a station running, flashing sprinkler icon ( ), or an arrow pointing towards running, it sounds like the controller is doing its part. Maybe the water has been shut off to the zone valves. Go to the zone valve and turn …
The Pro-C controller is modular in design. This means that most controller components can be removed and replaced if needed. For the newer style Pro-C (blue panel and buttons), the part number for the front panel is 821501. The panel fo the older PC-300 …
Rotary sprinklers require a certain amount of pressure and flow to operate properly. If the rotor does not receive the pressure it needs to pop up a leaky head will result. Here are some things to look for when a rotor doesn't pop up properly: Problem: …
Over time general usage can cause riser seals to wear out, similar to the wiper blades on a car, they require replacement. The signs of this are usually heads that have riser stems stuck up after the operation, or excessive leaking around the riser seal …
Hunter manufactures an MP Gauge , this gauge can be used on all Hunter spray heads. Simply screw the Hunter nozzle of your choice onto the MP Adapters top thread, then apply the MP Adapter's bottom thread to the spray head's riser stem. MP Gauge includes: …
All program information and manual watering is conducted with the WVP and individual WVC controllers using radio signals. Under normal conditions, these operations can be conducted up to 100 feet from the controller. The Transmit/Receive button on the …
The CLIK DELAY option is designed to set number of days for watering to remain off, after sensor has been activated and restored. … X2 - …
Here is a list of the error codes and ways to troubleshoot them: X2 - Controller code CODE description SOLUTION FAIL Wi-Fi setup failed Check the spelling of the network name (SSID) and/or password and reconnect to Wi-Fi donE The previous operation is …
NOTE: Complete this section only if you have a master valve installed in your irrigation system. A master valve is a “normally closed” valve installed at the supply point of the main line that opens only when the controller initiates a watering …
A Hunter CLIK sensor or closed circuit type weather sensors can be connected to the X2. The purpose of this sensor is to stop automatic watering when weather conditions dictate. … X2 - Connecting a CLIK …
The X2 Controller is compatible with Hunter Remote Controls (not included). The SmartPort® wiring harness (included with all Hunter Remotes) allows for fast and easy use of the Hunter controls. The Hunter remotes make it possible for you to operate the …
Before securing the controller to the wall, you must first remove the lower wiring compartment door. The door can easily be removed by following the simple steps below: Open the external door using the included key if outdoor version model. Indoor version …
Sometimes the EC can retain an electrical glitch, and the result can be some programming anomalies such as the freezing of the AM/PM adjustment. Be sure the controllers programming dial is in the AUTOMATIC position before performing this reset procedure: …
Interval Watering is a feature that allows you to select the number of days to pass before the next watering day. For example, an interval of 3 will cycle the program once every three days and water on the third day. An interval of 1 is every day and an …
The X-Core allows you to program a No Water Day(s). This feature is useful to inhibit watering on specific day(s). For example, if you always mow the lawn on Saturdays, you would designate Saturday as a No Water Day so that you are not mowing wet grass. …
Here are some common reasons why a pop-up sprinkler may stay stuck up: Debris in the pop up body The riser is damaged The riser seal is worn To fix this: Unscrew the body cap Pull out the sprinkler assembly Examine the parts Clean out debris Replace …
A valve with an external leak can be a simple adjustment or may require further inspection. Review our simple checklist below. Crack in the body - This would require a valve replacement. Loose bolts/screws on the bonnet - Tighten down, so they are snug. …
Here are some tips for valve repair. … Valves - Servicing Jar-Top Valves …
When using the side strip nozzles, there are several different configurations that can be done with any given design. For this reason, we do not publish a PRECIPITATION RATE for these models. We would recommend using the TOTAL AREA METHOD to calculate …
For accurate Solar Sync measurements, the controller needs to be programmed for the average peak season ET for your region. Use the table below to determine your region. The table will assist you in identifying the type of region you live in. There are …