Residential & Commercial Irrigation
Residential & Commercial Irrigation
Manual operation allows you to run a manual cycle from 0:01 (one minute) to a maximum of 6:00 (six hours). With the app open, select the MANUAL HAND icon. Select a RUN TIME . Click START . Click STOP to stop the manual operation. … Manual operation …
A controller with a partial or blank display usually has damage to an electronic component on the internal circuit board. Normally this type of damage cannot be repaired. If the controller was installed outside be sure that the door remains closed …
The "NO AC" or "Blank" display is a diagnostic message telling you that the controller has stopped receiving AC power. For the "NO AC" message, the controller is most likely running on the power supplied by the backup battery. Check the power source …
The NO AC display is a diagnostic message telling you that the controller has stopped receiving AC power. The controller is running on the power supplied by the backup battery. Check the power source by plugging a lamp or radio into the wall outlet to …
Step 1. Check the controller programming Is there a watering Start Time programmed into the controller? Is the Watering Start Time programmed with correct time of day (i.e. AM or PM)? Is the Current Time set correctly (i.e. AM or PM)? Is today a Water …
CONTROLLER SETTINGS offers more advanced features that can be accessed using the steps below. Open the Node-BT App and choose a controller Name. Select Connect . Select the More hamburger icon. Select Controller Settings . Location, Controller Name, …
If your Hunter SRC controller’s display reverts back to the current time after trying to manually activate stations, it has more than likely undergone a power surge or is experiencing a technical anomaly. Most likely this controller will need to be …
The dry out time could be as little as 4 hours depending on the weather conditions (temperature and humidity) and the rain threshold that is set. If the weather conditions remain cold and damp, your sensor could be active for months. Hunter Rain Sensors …
The DASHBOARD screen provides an overview of the programming within the app. Node controller battery strength (%) - This allows user to determine when battery need to be changed. Controller is set for AUTO or OFF - AUTO means controller will run per …
MANUAL OPERATION will allow you to turn on the following without changing any of the automatic settings. Existing program (A, B or C) - This allows you to turn on a program that has set run times and stations automatically programmed. Single station - …
Odd or Even day watering schedules are available on all Hunter controllers. … This feature uses numbered day(s) of the month for watering instead of specific days of the week (odd days: 1st, 3rd, 5th, etc.; even days: 2nd, 4th, 6th, etc.) With the cursor …
Facepack Identification Stops all irrigation; enables and disables Rain Shutdown. Sets run times and order for stations and Blocks. Accesses multiple options and controller settings. Different sets of options appear, depending on mode controller is in …
In order to properly handle your requests for any Hunter products under warranty, we need to know the date of manufacture for the items in question. Below you will find basic information on how to locate and read the date code on a variety of Hunter Golf …
STEP ONE STEP TWO 1. From the home screen start by pressing the "Options" button. 2. Continue pressing the "Options" button until "Edit FC Settings" displays. FC stand for "Field Controller" as IDS system's are often referred as in the Golf industry. …
Simply twist the solenoid on the valve counter clockwise 1/4 turn to 1/2 a turn. To shut off the valve, twist the solenoid clockwise until it is snug on the valve. … How do I manually open a zone control valve without using the …
The X-Core is compatible with the Hunter Solar Sync. Solar Sync is a sensor system that will automatically adjust the X-Core controller’s watering run times (based on changes in local climate condition) by using the Seasonal Adjust function. The Solar …
After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …
After programming the X-Core, set the dial to the RUN position to enable automatic execution of all selected watering programs and start times. … X-Core - Automatic …
To stop a station from running when the system cycles automatically, simply remove all station Run Times for station that you do not to operate. Make sure Programs A, B, C and on some controllers Program D, have a run time set to "0:00" for station that …
If your controller shows irrigation running (Flashing Sprinkler Icon), and your sprinklers are not working, you may have a wiring problem at the valves or the irrigation water supply has been shut down. If you have a master valve on your system (check for …
There are a number of reasons why the sprinklers may not come on from the automatic program. Assuming the controller will run the zones from the controller manually, you most likely have a programming issue. Below are a few possible causes to the …
This feature allows you to quickly diagnose wiring problems with your controller. Instead of having to check each field wiring circuit for potential problems, you can use the Hunter Quick Check circuit test procedure. To initiate the Quick Check test …
The X-Core is compatible with the Hunter Wireless Solar Sync. Solar Sync is a sensor system that will automatically adjust the X-Core controller’s watering run times (based on changes in local climate condition) by using the Seasonal Adjust function. The …
For accurate Solar Sync measurements, the controller needs to be programmed for the average peak season ET for your region. Use the following table for choosing your region. You can use methods A, B or C to help you choose which region is best for your …