Residential & Commercial Irrigation
Residential & Commercial Irrigation
When using the side strip nozzles, there are several different configurations that can be done with any given design. For this reason, we do not publish a PRECIPITATION RATE for these models. We would recommend using the TOTAL AREA METHOD to calculate …
A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time. NOTE: In the Start Times dial position, the numbers …
W e would prefer that you use a Hunter valve with a Hunter DC latching solenoid, but we realize that sometimes you may be retrofitting existing systems that have another manufacturer’s valves. We have done testing on the following solenoids and have found …
Solar power eliminates the need for batteries and provides maintenance-free operation by harnessing the sun's energy or ambient light to fully power the controller 24 hours a day, 7 days a week, for years on end. This "eco-innovations" alternative is more …
Eco-Mat and PLD-ESD - Installation Details …
Recommended Eco-Mat installation depth per plant type: Turf: 4-6 inches (10-15 centimeters), Perennials and groundcovers: 8 inches (20 centimeters), Shrubs: 12 inches (30 centimeters. Recommended to achieve 80-85 percent compaction rate of soil above and …
Run Eco-Mat parallel to longest irrigated area length to ensure quick installation and to minimize fitting quantities. To calculate Eco-Mat row quantity for a specific area, divide the shorter side of the area by 26 inches (66 centimeters). The width of …
Establish a firm header (entry manifold) on the shortest side of irrigated area. A PVC entry manifold is recommended for durability and stability. Install each manifold below the mat, or otherwise far enough away from the curb, so as not to prevent the …
Eco-Mat is particularly effective with rooftop gardens where the growing medium is very lightweight and porous. Typical dripline cannot succeed well within this soil profile, yet the Eco-Mat performs extremely well. Always refer to the project engineer or …
Open the manual flush valve at the exhaust manifold and pressurize the system to thoroughly remove debris within the dripline. Flush until water runs clear. This could take several minutes for larger systems. Close the manual flush valve and run each zone …
In general, slightly sandy soil (sandy loam) is ideal for subsurface irrigation; this is because “medium” textured soils have the greatest amount of water available to plants due to lower capillary forces. Follow recommendations from the soils report. …
We recommend using a temporary supplemental overhead irrigation system to establish plant material in conjunction with the subsurface system. Temporary supplemental overhead irrigation can be stopped once roots have grown into the irrigated zone. …
Install and use soil moisture sensor (Soil-Clik®) on or just above the mat to maximize water savings and reduce overwatering. … Eco-Mat - moisture …
Roots can, and likely will, grow through the mat. The PET fleece defends against root intrusion into the emitters without injecting toxic chemicals or harmful metal byproducts into the soil. … Eco-Mat - Root …
Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … HEMT - Hunter Emitter Multi-Tool … Dripline …
The Roam XL Owner's Manual will guide you through the installation, wiring and operation of the Roam XL irrigation remote. … Roam XL Owner's …
The Roam Owner's Manual will guide you through the installation, wiring, and operation of the Roam irrigation remote. … Roam Owner's …
When using a ROAM, ROAM-XL, ICR, or SRR remote, you may come across a controller that gives you an ERR or SP ERR message. There are two reasons that would cause one of these messages. Miswired Smartport Wrong Station Count on Transmitter … CAUSE - Noise …
Your ICR Transmitter comes from the factory with the maximum number of stations set to 9. This means that when you use the UP or DOWN buttons to change the station, you may change it to any number between 1 and 9. However, if you have controllers …
The HPC face panel quickly and easily upgrades Pro-C® controllers (PC400 models manufactured since March 2014) to next-generation smart controllers via the Hydrawise platform. It also allows end users and contractors to manually operate their systems …
The Flow-Clik Interface Box has a System Status indicator LED that provides information on the current status of the Flow-Clik system. RED indicates an unacceptable amount of water was flowing and the system has been shut down. (Water flow exceeded the …
Using the Flow-Clik Interface Box, the sensor is calibrated by pressing the Calibrate button while the highest flow zone is operating. While the system is learning the flow, the System Status Indicator light will be yellow. After a 10 second period of …
Now that the internal and external components are installed, turn on the system to verify functionality with the on-off-auto selector switch. Next, set the rotor arc. The ST-1600-HS-B Rotor has an arc range of 40° to 360°. It also has a ratcheting feature …
If your sensor is not turning controller back on after a rain event, you may have debris in the spindle of the rain sensor. Remove the spindle assembly to check for debris or damage to the disks. … Pry upward on both sides of the middle stack of the …