Residential & Commercial Irrigation
Residential & Commercial Irrigation
The Flow-Sync Sensor is designed to be installed within an FCT tee fitting, sized for the pipe in which it will be installed. Optional slip-BSP adapters are available separately for sizes up to 75 mm for international applications. Install the FCT tee …
All in-vault installations require the ST-IBS-1600 Infill Barrier System to blend the ST System with the surrounding field. The Infill Barrier System also creates a snug fit between the rotor and the vault cover, allowing for smoother operation. For …
Before attaching synthetic, track, or concrete material to the vault, cover, and Infill Barrier System, trim the walls of the Infill Barrier System to create a flat upper surface if using non-infill type material. If an infill-type material is being used, …
The FCT tee fitting comes with a plug that allows for installation of the FCT into the irrigation system prior to installing the Sensor. This allows the FCT tee to be installed separately from the sensor and prevents damage to the sensor during …
Operating Specifications Temperature Pressures Humidity 0 to 140ºF/60ºC up to 200 psi/13.7 bar up to 100% Flow Range Flow-Sync Sensor Diameter Operating Range (Gpm) Minimum* Suggested Maximum** 1" 2 17 1½" 5 35 2" 10 55 3" 28 120 4" 34 195 * Minimum …
Remove the sensor jumper across the two SEN terminals in the controller. Attach the two yellow wires to the 24 VAC terminals. Attach the blue wire to one SEN terminal and the white wire to the other SEN or SEN COM terminal. NOTE: Additional setup steps …
The receiver has two LED lights that indicate the state of the system. SENSOR STATUS LED: RED : Sensor is wet (watering disabled) GREEN : Sensor is dry (watering enabled). YELLOW : Sensor is in addressing mode. SENSOR BYPASS LED: RED: Rain sensor is …
Find a Distributor PART NUMBER DESCRIPTION WM-CLIK-TR Wireless Mini-Clik Sensor transmitter only WR-CLIK-R Wireless Mini-Clik Sensor receiver only 10023600SP Wireless Mini-Clik Sensor cap with spindle assembly 10023900SP Wireless Mini-Clik Sensor quick …
Tips for Mounting the Sensor -Choose a location such as the side of a building or post. The closer the transmitter is to the receiver, the better the reception. Do not exceed 800' (243 m). -To ensure maximum range in communication, mount the receiver …
Manual Test Spindle: Press and hold the manual test spindle to confirm the proper operation of your sensor. Vent Cap and Spindle: Used to adjust reset rate or dry out time for the sensor. Radio Antenna: Transmits a wireless signal to the receiver up to …
Wiring the Sensor to the Interface Box The red and black leads from the Flow-Clik sensor are connected to the red and black leads on the Interface Box. A minimum wire size of 18-gauge wire can be used to connect the leads from the sensor to the …
WARNING! Flow-Sync is only designed for low-voltage connection to approved irrigation controller flow terminals. do not install in high-voltage 110V or 230V circuits. Flow-Sync has two wire leads for the controller connection. These may be extended up to …
Reece Irrigation & Pools …
Quick couplers allow fast access to water while maintaining in-ground durability and vandal resistance. A quick coupler valve is a great tool to use when the rotor does not need to be turned on to irrigate a large area, and it’s only needed for spot …
When designing and installing irrigation systems, the water stream's trajectory and spray height leaving a sprinkler nozzle is important information. The chart below will show the total feet of height when using the largest nozzle for the ST-1600 model. …
The Mini-Clik is an adjustable model which can be set to deactivate the system when either 1/8”, 1/4”, 1/2”, 3/4” or 1” (3-25mm) of rain hits the sensor. … Mini-Clik - Amount of Rain to Activate …
The difference between the Mini-Clik and the Rain-Clik is that the Mini-Clik adjusts for rainfall of 1/8" to 1". As the moisture-laden disks expand, they will eventually activate a switch that interrupts the circuit from the controller to the solenoid …
The on-off-auto selector switch allows the user to control the kit to automatically actuate from an irrigation controller or manually from the switch. To install the switch, make sure it’s positioned directly below an access port in the vault’s cover set. …
After installing the on-off-auto selector switch, insert the supply tubing from the switch into the control valve. This allows you to turn the valve on and off, either manually from the switch or automatically from the controller. On the control valve, …
Using the Flow-Clik Interface Box, the sensor is calibrated by pressing the Calibrate button while the highest flow zone is operating. While the system is learning the flow, the System Status Indicator light will be yellow. After a 10 second period of …
The Flow-Clik Interface Box has a System Status indicator LED that provides information on the current status of the Flow-Clik system. RED indicates an unacceptable amount of water was flowing and the system has been shut down. (Water flow exceeded the …
This section will give you a brief overview of some of the components of the Flow-Sync system. … Impeller: Rotates when flow is occurring O-rings: Provides sealing of sensor in sensor body Wires: Black and red wires connect sensor to the ACC or I-Core …
For installation of Root Zone Watering System with existing trees, follow the steps below. … Note: To service the RZWS, use a tool to access and release the two snaps from the cap. … RZWS - Existing Tree …
The 18" and 36" Root Zone Watering Systems feature a new top design that offers improved durability. The top now consists of two pieces: a body that holds onto the tubing, and a cap to snap onto the body. To remove the cap for serviceability, use a …