Residential & Commercial Irrigation
Residential & Commercial Irrigation
Connect a 9-volt alkaline battery (not included) to the battery terminals and place in the battery compartment in the front panel. The battery allows the user to program the controller without AC power. Watering will not occur without AC power. Since this …
Route a wire pair from the pump relay into the controller housing. Connect the pump common wire to the terminal slot “ COM ” (Common) and the remaining wire from the pump relay to the P/MV terminal slot. Relay holding current draw must not exceed 0.28 …
Connect either wire from Master Valve to the P/MV terminal at the base of module. Connect remaining wire to the “COM” (Common) terminal. … Pro-C - Connecting a Master …
Point Source Support …
This feature permits the user to stop all programmed waterings for a designated period from 1 to 31 days. At the end of the programmable rain off period, the controller will resume normal automatic operation. Turn the dial to the SYSTEM OFF position. …
The Pro-C provides simplified testing of a rain sensor when the sensor is wired into the sensor circuit. You can manually test proper operation of the rain sensor by using the One Touch Manual Start. During the Manual All stations cycle, pressing the test …
The Pro-C controller is supplied with a factory-installed base module for up to 4 stations on the PC-400 and up to 3 stations on the older PC-300. Additional modules may be added in increments of 3 stations (PCM-300) or a single 9-station (PCM-900) to …
The Pro-C controller can activate 2 Hunter Solenoids per station terminal plus a master valve. … Pro-C - Maximum Solenoids per Station …
LCD Display Main Display: Indicates various times, values, and programmed information Year: Identifies current calendar year Month: Identifies current calendar month Day: Identifies current calendar day Start Time: Identifies selected program start time …
After programming is complete, turn the dial to the RUN position to enable automatic execution of all selected programs and start times. … Pro-C - Automatic …
All necessary hardware is included for most installations. Use the hole at the top of the controller as a reference and secure a 1" (25 mm) screw into the wall. Note: Install screw anchors if attaching to drywall or masonry wall. Align controller with the …
Welcome to the Flow-Sync sensor support section. The Flow-Sync or HFS is a sensor that monitors the flow of water running through a pipe, when flow is at an abnormal level the Flow-Sync and controller communicate to shut off the irrigation. In this …
Solar Sync Delay for Pro-C The delay feature is accessible only after the installation of the Solar Sync. The Solar Sync Delay feature allows the user to postpone seasonal adjustment changes from being made by Solar Sync for up to 99 days. While the Solar …
Cause The Solar Sync sensor is not connected to the controller The Solar Sync sensor wires may have a break in them or a bad connection Solution Connect the Solar Sync to the "SEN" positions on the wiring terminal - The display will then show the Region …
If a Solar Sync sensor has been installed on the Pro-C controller then the seasonal adjust value used by the controller will be calculated from the weather data supplied by the Solar Sync sensor. If it is decided that the Solar Sync sensor will no longer …
For accurate Solar Sync measurements, the controller needs to be programmed for the average peak season ET for your region. Use the following table for choosing your region. You can use methods A, B or C to help you choose which region is best for your …
After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …
The word USED displayed on the Pro-C Controller represents a landscape lighting station that was assigned. Once a start time is assigned to program L1, it turns station 1 from an irrigation station to a lighting station (same for L2 and L3). As a result, …
You can also activate a program to water without using the dial. … With the dial in the RUN position, hold down the button for 2 seconds. This feature automatically defaults to program A. You can select program B, or C by pressing the PRG program. The …
Valves currently watering will be shut off after the dial is turned to the SYSTEM OFF position for two seconds. All active programs are discontinued and watering is stopped. To return controller to normal automatic operation, simply return dial to the RUN …
The Pro-C is compatible with Hunter remote controls. The SmartPort wiring harness (included with all Hunter remotes) allows for fast and easy use of Hunter controls. Hunter remotes make it possible for you to operate the system without having to walk back …
From the Home screen, touch the Settings button and then the Wireless button. Select your wireless network from the list shown on the controller display and press the Confirm button on the screen. Enter your wireless password and press the OK button on …
The Events log is the Hydrawise time stamp for all controller activity. It provides a detailed description of all actions, including manual operations, station runs, flow usage, program changes, and who authorized the changes. … Light Blue Icon - These …
Controller Settings lists essential information about your controller. This section allows you to change your Controller Name, edit or remove the Serial Number, change Weather Stations, set Interzone Delay, and access other Advanced Settings. … Name - The …