Residential & Commercial Irrigation
Residential & Commercial Irrigation
The Roam Owner's Manual will guide you through the installation, wiring, and operation of the Roam irrigation remote. … Roam Owner's …
The EZ Decoder System is a unique two-wire output option for Hunter ICC2 and HCC controller models only. Do not attempt to use this system with any other model or brand of controller. Do not attempt to use EZ-1 decoders with any other decoder controller. …
When using a ROAM, ROAM-XL, ICR, or SRR remote, you may come across a controller that gives you an ERR or SP ERR message. There are two reasons that would cause one of these messages. Miswired Smartport Wrong Station Count on Transmitter … CAUSE - Noise …
Your ICR Transmitter comes from the factory with the maximum number of stations set to 9. This means that when you use the UP or DOWN buttons to change the station, you may change it to any number between 1 and 9. However, if you have controllers …
Your ROAM XL System is pre-addressed to work right out of the box. However, if you changed the Transmitter address as described in the section, Preparing the Transmitter For Use", you must allow the Receiver to learn the new address. This can be done by …
Power must be removed from the transmitter by removing at least one AAA battery from the battery compartment on the back of the unit. Press both the On and Off buttons simultaneously while re-inserting the AAA battery. Release both buttons and check the …
The HPC face panel quickly and easily upgrades Pro-C® controllers (PC400 models manufactured since March 2014) to next-generation smart controllers via the Hydrawise platform. It also allows end users and contractors to manually operate their systems …
Due to the rapid acceptance of the Hunter ROAM amongst Hunter Irrigation Products suppliers and end users, this Support Article is dedicated to the installation guidelines of our remote control kit. Preparing the Communication Port To utilize the ROAM and …
Welcome to the Remotes Support section. Here you will find informative videos and owner's manuals with instructions for installing and operating your Hunter irrigation remote. … …
Welcome to the Solar Sync sensor support section. The Solar Sync sensor comes in wired and wireless versions and will automatically adjust the controller run time based on the sensors reading of the weather. In this section you will find information on …
Operating Specifications Station Count: Conventional wiring from 4 to 23 stations,two-wire EZ Decoder System option up to 32 stations. Station Run Time: 1 minute to 6 hours (optional Seconds Mode) Start Times: 4 individual starts per program, three …
A Control Dial B Wiring Compartment 1 Run Normal dial position for automatic operation 1 9 V Battery An alkaline battery (not included) allows programming of the controller facepack without AC power 2 Set Date/Time Set the current date and time 2 …
All necessary hardware is included for indoor and outdoor installations. Use the hole at the top of the controller as a reference and secure a 1" (25 mm) screw into the wall. Note: Install screw anchors if attaching to drywall or masonry wall. Align the …
P2C models are prewired with a power cord and plug for simple installations in both indoor and outdoor applications. If the controller is to be powered by direct line voltage, follow these wiring instructions: Route AC power cable and conduit through the …
The Pro-C Controller is supplied with a factory-installed base module for up to 4 stations. Additional modules may be added in increments of 3 stations (PCM-300), 9 stations (PCM-900), or 16 stations (PCM-1600). In total, a conventionally wired system can …
Route valve wires between control valve location and controller. At valves, attach a Common wire to either solenoid wire of all valves. This is most commonly a white wire. Attach a separate control wire to the remaining wire of each valve. All wire splice …
Connect either wire from the Master Valve to the P/MV terminal on the 4-station base module. Connect remaining wire to the COM (Common) terminal. … P2C - Connecting a Master …
Route a wire pair from the pump relay into the controller housing. Connect the pump Common wire to the terminal slot COM (Common) and the remaining wire from the pump relay to the P/MV terminal slot on the 4-station base module. The relay holding the …
A Hunter weather sensor or other micro-switch-type weather sensors can be connected to the Pro-C® Controller. The purpose of this sensor is to stop automatic watering when weather conditions dictate. Remove the metal jumper plate that is attached across …
The P2C Controller is compatible with Hunter remote controls. The SmartPort Wiring Harness (included with all Hunter remotes) allows for fast and easy use of Hunter controls. Hunter remotes make it possible to operate the system without walking back and …
The P2C Controller can be made “smart” with the addition of a Solar Sync ET Sensor. This advanced weather sensor calculates daily evapotranspiration (ET) rates and adjusts irrigation schedules based on local weather conditions. In addition, the sensor …
Turn the dial to the DATE/TIME position. The current year will flash in the display. Use the + or - buttons to change the year. Push the → button to set the month. The month will flash. Use the + or - buttons to change the month. Press the → button to set …
Turn the dial to the START TIMES position. Press the PRG button to select A, B, or C. Use the + and - buttons to change the start time. (Advances in 15-minute increments.) One start time will activate all stations sequentially in that program. Press the → …