Residential & Commercial Irrigation
Residential & Commercial Irrigation
Hunter rotary sprinklers operate on a “gear drive” system. When in operation, water turns a small turbine in the base of the sprinkler, which drives a series of gears that cause the head to rotate. The Hunter gear drive mechanism is sealed from dirt and …
Fault Messages Faults: Controller display shows “Fault”. This may be followed by a station number. The Station Status light on the ICore System Status dashboard will also show a red LED when there has been a decoder fault. Note: Fault light and message …
For accurate Solar Sync measurements, the controller needs to be programmed for the average peak season ET for your region. Use the table below to determine your region. The table will assist you in identifying the type of region you live in. There are …
The X-Core allows the user to program the controller so that the sensor disables watering on only desired stations. For example, patio gardens that have pots under overhangs and roofs may not receive water when it rains and will continue to need to be …
Turn off the controller power using the power switch on the transformer. … Remove the dust cover, or existing module, from the bottom rear of the controller facepack. Push up on the spring-loaded button and pull downward to remove. Slide in the new module …
The PSR-B was developed to provide a solution for irrigation controller and pump start relays installations that have insufficient power to energize the pump relay. A common cause for this problem is the use of too small a wire size for the distance from …
REL 2 is used to allow multiple controllers to operate the same low-voltage device (Master Valve or Pump Start Relay). IMPORTANT: REL 2 is NEVER connected to high voltage. It is for 24VAC devices, only. Diagrams listed below: … … … Two Controllers With …
The chattering you hear on a pump start relay is usually caused by insufficient amperage arriving at the relay from the controller. The first question you should ask yourself is – Did this Relay work for some time before or is this new installation? New …
If the Solar Sync Seasonal Adjustment is too high or too low you may need to change the Water Adjustment feature on your controller or Solar Sync Module on older models. This will allow you to fine-tune your station Run Times to allow for more watering or …
Here is a list of the error codes and ways to troubleshoot them: … CAUSE - The Station # ERR (for example 1 ERR) is a diagnostic message that appears when your controller is detecting a fault on that corresponding irrigation zone. SOLUTION - To …
Choose from the links below for troubleshooting your PRO-C controller. Station Repeats No Display SP Err ERR with Station # No AC Sensor Off Message Rain Sensor will not Shut Off System Controller does not have a start time for each station. Flashing …
You can access reports for your controllers by selecting REPORTS at the bottom for the mobile version. Use the settings on the report tab to the right of the screen to change the following: Change the range of the report Clear all report data Refresh a …
Installing and maintaining an irrigation system is a complex task. That's why it's best to hire a qualified professional. Get connected with a local authorized landscape professional. Find A Contractor Hunter is dedicated to connecting our customers with …
With this option, you can select interval watering from 1 to 31 days. This feature is convenient if you want to have a more consistent watering schedule without having to worry about the day of the week or the date. The interval you select is the number …
When programming your NODE BT controller, you can change the NAME for each zone(station) to make it easier to identify the different areas of your landscape. … From the HOME dashboard, select the MORE tab on the lower right side of the screen. Select …
The BTT controller retrieves the local date and time from the smartphone it is paired with and updates every time a smartphone device is connected. The date and time for the controller can only be changed via smartphone settings. You can test by setting a …
Your ROAM Transmitter comes from the factory with the maximum station number set to 15. This means that when you use the UP and DOWN buttons to change the station, you may change it to any number between 1 and 240. However, if you only have a 6-station …
The EZ-DT is a handheld, battery-operated device used for field diagnostics and troubleshooting with EZ Decoder Systems. Innovative wireless communication from the EZ-DT to EZ-1 decoders permits fault detection in the field without removing the decoders …
The CUSTOM IMAGE feature allows the user to add an image from their existing phone library or the option to take a new one. This is a useful tool when you have multiple controllers/stations on-site to identify locations. NOTE: The app version 5.0.1869 …
To allow P/MV switching of water sources on sensor inputs, each station will need to be enabled for both P/MV outputs. When the sensor is triggered (open or closed), the P/MV that is not in use will be set to "Close P/MV." Depending on the status of the …
After connecting one or more flow sensors to the controller, the next step is to configure the sensor in the FLOW SENSORS menu. The controller has three Flow Sensor inputs built-in, but three more can be added with the A2C-F3 Flow Expansion Module. ACC2 …