Residential & Commercial Irrigation
Residential & Commercial Irrigation
The standard MP Rotators have a matched precipitation rate of approximately 0.4 in/hr. This means any standard MP Rotator at any arc or radius can be placed on the same zone. The MP800SR can be configured to work well in head-to-head coverage in either …
The CLIK DELAY option is designed to set number of days for watering to remain off, after sensor has been activated and restored. … X2 - …
NOTE: Complete this section only if you have a master valve installed in your irrigation system. A master valve is a “normally closed” valve installed at the supply point of the main line that opens only when the controller initiates a watering …
Here is a list of the error codes and ways to troubleshoot them: X2 - Controller code CODE description SOLUTION FAIL Wi-Fi setup failed Check the spelling of the network name (SSID) and/or password and reconnect to Wi-Fi donE The previous operation is …
A Hunter CLIK sensor or closed circuit type weather sensors can be connected to the X2. The purpose of this sensor is to stop automatic watering when weather conditions dictate. … X2 - Connecting a CLIK …
The X2 Controller is compatible with Hunter Remote Controls (not included). The SmartPort® wiring harness (included with all Hunter Remotes) allows for fast and easy use of the Hunter controls. The Hunter remotes make it possible for you to operate the …
The chart below indicates the maximum wire runs that can be used when installing Hunter AC solenoid valves with controllers. The example in the chart below demonstrates the most commonly used wire size for station control and ground wire ( e.g.,12 AWG = …
A schedule (program) needs 3 things for the controller to run automatically. START TIME for the program. RUN TIME for at least one station in that program. DAY TO WATER for the program. The NODE-BT controller has three programs (A, B, or C) for irrigation …
Download the free Hunter NODE-BT app to a smartphone device from the iTunes® Store for iOS® devices, or the Google Play™ store for Android™ devices. Requires iOS 9.0 or later. Compatible with iPhone®, iPad®, and iPod touch® devices. Requires Android 5.0 …
Inner Door – Opens to main wiring compartment AC Wiring compartment – For connection of 120/230V AC power with 1 x 0.75" (19 mm) conduit opening Fuse – 2 Amp (fast) 250V, 6 x 20 mm Conduit Openings, Low Voltage – 2" x 2½" (64 mm), 2" x ¾" (19 mm) Wire …
Adding the controller to the Centralus software will require a few simple steps. You must have a free Hunter SSO account to add a controller. Learn More NOTE: If you see the message DEVICE ALREADY CLAIMED , please get in touch with the original …
NOTE: Complete this section only if you have a pump start relay installed. A pump start relay is a device that uses a signal from the controller to actuate a separate electrical circuit to energize a pump to provide water to your system. The controller …
Turn off the controller power using the power switch on the transformer. … Remove the dust cover, or existing module, from the bottom rear of the controller facepack. Push up on the spring-loaded button and pull downward to remove. Slide in the new module …
REL 2 is used to allow multiple controllers to operate the same low-voltage device (Master Valve or Pump Start Relay). IMPORTANT: REL 2 is NEVER connected to high voltage. It is for 24VAC devices, only. Diagrams listed below: … … … Two Controllers With …
The chattering you hear on a pump start relay is usually caused by insufficient amperage arriving at the relay from the controller. The first question you should ask yourself is – Did this Relay work for some time before or is this new installation? New …
With the Pro-C controller in production for 23 years, we have continuously upgraded to accommodate the innovative features. Below, you will find every panel we manufactured for the Pro-C model, including the wifi replacement front panel. For information …
You can access reports for your controllers by selecting REPORTS at the bottom for the mobile version. Use the settings on the report tab to the right of the screen to change the following: Change the range of the report Clear all report data Refresh a …
Installing and maintaining an irrigation system is a complex task. That's why it's best to hire a qualified professional. Get connected with a local authorized landscape professional. Find A Contractor Hunter is dedicated to connecting our customers with …
With this option, you can select interval watering from 1 to 31 days. This feature is convenient if you want to have a more consistent watering schedule without having to worry about the day of the week or the date. The interval you select is the number …
When programming your NODE BT controller, you can change the NAME for each zone(station) to make it easier to identify the different areas of your landscape. … From the HOME dashboard, select the MORE tab on the lower right side of the screen. Select …
The BTT controller retrieves the local date and time from the smartphone it is paired with and updates every time a smartphone device is connected. The date and time for the controller can only be changed via smartphone settings. You can test by setting a …
Your ROAM Transmitter comes from the factory with the maximum station number set to 15. This means that when you use the UP and DOWN buttons to change the station, you may change it to any number between 1 and 240. However, if you only have a 6-station …