Residential & Commercial Irrigation
Residential & Commercial Irrigation
When using the side strip nozzles, there are several different configurations that can be done with any given design. For this reason, we do not publish a PRECIPITATION RATE for these models. We would recommend using the TOTAL AREA METHOD to calculate …
Node Program Capablities The NODE uses standard Hunter controller programming with 3 programs (A, B, C) and 4 start times per program. … On standard Hunter controllers a dial is used to scroll between the programming functions, however, on the NODE the …
Push the button until the icon is displayed. All 4 digits will be displayed representing the year. Use the or buttons to change the year. Press the button to proceed to setting the month. All 4 digits will be displayed with the two digits on the …
The ACC controller can be reset, erasing some, or all programmed information. There are 5 different levels of reset command available. Once any of them is chosen, the information will be permanently erased. Turn the dial to the RUN Position. Press and …
The Pro-C is compatible with the Hunter Solar Sync. Solar Sync is a sensor system that will automatically adjust the Pro-C controller’s watering run times (based on changes in local climate condition) by using the Seasonal Adjust function. The Solar Sync …
NOTE: In the Start Times dial position, the numbers 1-4 do not represent stations. The numbers represent the program start times. Each program can start up to 4 times on the set days to water. One start time will activate all stations sequentially in that …
For drip irrigation systems using BTT, we recommend using regulation and filtration systems on all residential and commercial applications. Filters shall install directly on BTT's 3/4" hose thread outlet and connect to drip tubing providing regulated …
This is strongly discouraged by Hunter for the following reasons: It is unlikely that the pre-existing wire meets the specifications for gauge, twist, and solid copper. Pre-existing wire will not be color-coded correctly for the decoder wires. …
Controller power must be OFF when installing decoders in the two-wire path. Note: Decoder wire runs and connections must be completely waterproof. Decoder wiring is more critical than "conventional" 24 VAC solenoid wiring. Follow instructions closely! …
The chart below indicates the maximum wire runs that can be used when installing Hunter AC solenoid valves with controllers. The example in the chart below demonstrates the most commonly used wire size for station control and ground wire ( e.g.,12 AWG = …
Download the I-Core Owner’s Manual for detailed instructions on installation and programming an I-Core irrigation controller. … I-Core Owner's …
Download the DUAL Owner’s Manual for detailed instructions on how to install and program the two-wire decoder system for the I-Core irrigation controller. … DUAL Owner's …
The three sensors combined on this product are for wind speed, rainfall and temperature (near-freezing conditions). Each sensor operates independently of the other; therefore, any or all of them may be switching at a given moment. See the enclosed …
A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time. NOTE: In the Start Times dial position, the numbers …
The standard MP Rotators have a matched precipitation rate of approximately 0.4 in/hr. This means any standard MP Rotator at any arc or radius can be placed on the same zone. The MP800SR can be configured to work well in head-to-head coverage in either …
One station: At any time you can simply increase or decrease Run Time to any individual station in the host controller and that station will adjust up and down with all the rest of the stations from a new level. All stations: Use the water + and - feature …
Metal controllers will include a hole plug assembly in a pre-drilled factory hole on top of the controller. Remove the nut on the inside of the controller to remove the plug. Route the cable through the pre-drilled hole and the antenna nut. Then tighten …
After setting up an ACC2 or ICC2 controller in your Centralus account, you may choose to release the controller (serial number) to another user. This will require the controller's deletion. When the NEW user adds the controller into the Centralus …
When using Centralus Software, you have the ability to change your STATION , BLOCK , and/or DELAY RUN TIMES . There is a maximum run time of 12:00 hrs for all model A2C controllers. The minimum run time is 15 seconds for the decoder model and 1 …
Regulating pressure saves water and extends the life of the irrigation system. Water savings is achieved by operating each zone at the best pressure for that equipment and application type. Use the chart below to select the best Accu-Sync™ model for each …
Ensure you have a strong Wi-Fi signal. Wi-Fi coverage can be easily tested using a smartphone. A signal strength of two or three bars is recommended. Wi-Fi connectivity can also be tested on the HPC itself (signal strength is shown when you select a …
The rotor staking kit is designed to stabilize the shrub rotor while installed above ground. This rotor accessory is predominately used on slopes, either with the lateral pipe on the surface or slightly below the surface. Full installation details are …
When designing and installing irrigation systems, the water stream's trajectory and spray height leaving a sprinkler nozzle is important information. The chart below will show the total feet of height when using the largest nozzle for the ST-1600 model. …
This guide outlines the application, design, and installation of Hunter’s inline drip products that provide designers, installers, and irrigation managers a new class of irrigation technology. It is written for professionals who have a solid understanding …