Residential & Commercial Irrigation
Residential & Commercial Irrigation
If your sensor is not turning controller back on after a rain event, you may have debris in the spindle of the rain sensor. Remove the spindle assembly to check for debris or damage to the disks. … Pry upward on both sides of the middle stack of the …
The high velocities that are common during initial activation of an irrigation cycle could cause the Flow-Clik to sense a “high flow” situation (primarily due to air trapped within the system) and subsequently shut down the irrigation system at the …
The Flow-Clik monitors for a high flow condition, shutting down the system or individual zone when overflow occurs. Once the system has been shut off due to a high flow condition, the Flow-Clik turns the system back on automatically after a pre-selected …
This guide outlines the application, design, and installation of Hunter’s inline drip products that provide designers, installers, and irrigation managers a new class of irrigation technology. It is written for professionals who have a solid understanding …
The Automatic Flush Valve (AFV) allows debris to be flushed out of any dripline system. It is good practice to install an AFV at the end of any single dripline or grid of dripline. Flush the zone prior to use. An AFV may be used for any dripline system …
Similar to a sprinkler head, the Eco-Indicator pops up to provide visual indication that a drip system is operating. The Eco-Indicator has a highly visible yellow stem that pops up when the system is running at a pressure of least 12 PSI (0.8 bar; 83 …
Emitter tool for punching a pilot hole, inserting, and removing an emitter. … Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … Pocket Punch … HEMT - Hunter Emitter Multi-Tool … Emitter …
Wiring the Sensor to the Interface Box The red and black leads from the Flow-Clik sensor are connected to the red and black leads on the Interface Box. A minimum wire size of 18-gauge wire can be used to connect the leads from the sensor to the …
When designing and installing irrigation systems, the water stream's trajectory and spray height leaving a sprinkler nozzle is important information. The chart below will show the total feet of height when using the largest nozzle for the ST-1600 model. …
Using the Flow-Clik Interface Box, the sensor is calibrated by pressing the Calibrate button while the highest flow zone is operating. While the system is learning the flow, the System Status Indicator light will be yellow. After a 10 second period of …
The Flow-Clik Interface Box has a System Status indicator LED that provides information on the current status of the Flow-Clik system. RED indicates an unacceptable amount of water was flowing and the system has been shut down. (Water flow exceeded the …
Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … HEMT - Hunter Emitter Multi-Tool … Dripline …
When your controller is first powered on, it will run a short wizard to connect it to your wireless router. If you’re not using the initial startup wizard, go to the Wireless Settings section to make changes. For support, please contact …
Valve Wire Sizing (Maximum One-Way Distance in Feet Between Controller and Valve) Ground Wire Size Control Wire (ft) Below is a chart indicating the maximum wire runs that can be used when installing Hunter AC solenoids and valves. 18 AWG / 1.0 mm 16 …
We recommend that a qualified licensed contractor perform this type of winterization method. The blowout method utilizes an air compressor with a cubic foot per minute (CFM) rating of 80-100 for any mainline of 2" or less. The compressor is attached to …
Hunter MP Rotator Support MP Rotators are a high efficient rotating nozzle, to find more support on this product please go to the MP Rotator Support Section. Nozzle Models Available Hunter MP Rotators are available in two precipitation rates, MP Rotators …
To improve Wi-Fi visibility to the router, we recommend using the Wi-Fi extension kit (model: WIFI-EXT-KIT). This is not a signal booster, but an option to get the antenna closer to the router. Going around corners, through obstructions, or just reducing …
Use the CONTROLLER OFF feature to stop manual/automatic watering commands, set programmable days off (1-180 days), and set the controller off. Sign in to your C ENTRALUS ACCOUNT . Select a controller name from your CONTROLLER LIST . Click on the …
Radio Antenna – Transmits a wireless signal to the receiver up to 800 ft. (275m). It is recommended that the antenna be oriented vertically Vent Ring – Used to adjust the reset rate or dry out time for the sensors. Opening the vents will decrease the …
It is important to understand that Solar Sync provides a global seasonal adjustment to the controller. This means that all station run times will be modified by the seasonal adjustment percentage shown. When programming the controller, the run times …
When using the residential central Wi-Fi adapter with the I2C commercial controller, there are some common LED usage lights that will help you determine the communication. LED Description 1st Flash Red when in direct connect mode. Flash Green when …
Hunter warrants the Wireless Rain-Clik (WR-CLIK) for five years. If a defect in a Hunter product is discovered during the applicable warranty period, Hunter will repair or replace, at its option, the product or the defective part. This warranty does not …