Residential & Commercial Irrigation
Residential & Commercial Irrigation
It's important to have an irrigation design plan, and hydraulics (PSI and GPM) inspected at the site before installation. If necessary, please contact a professional . Hunter provides installation details for designing irrigation systems. You can download …
The three sensors combined on this product are for wind speed, rainfall and temperature (near-freezing conditions). Each sensor operates independently of the other; therefore, any or all of them may be switching at a given moment. See the enclosed …
For drip irrigation systems using BTT, we recommend using regulation and filtration systems on all residential and commercial applications. Filters shall install directly on BTT's 3/4" hose thread outlet and connect to drip tubing providing regulated …
The chart below indicates the maximum wire runs that can be used when installing Hunter AC solenoid valves with controllers. The example in the chart below demonstrates the most commonly used wire size for station control and ground wire ( e.g.,12 AWG = …
This is strongly discouraged by Hunter for the following reasons: It is unlikely that the pre-existing wire meets the specifications for gauge, twist, and solid copper. Pre-existing wire will not be color-coded correctly for the decoder wires. …
Controller power must be OFF when installing decoders in the two-wire path. Note: Decoder wire runs and connections must be completely waterproof. Decoder wiring is more critical than "conventional" 24 VAC solenoid wiring. Follow instructions closely! …
Turn off the controller power using the power switch on the transformer. … Remove the dust cover, or existing module, from the bottom rear of the controller facepack. Push up on the spring-loaded button and pull downward to remove. Slide in the new module …
Turn off the controller power. Tilt and remove the facepack to access the bottom of the facepack. Remove the dust cover or prior module from the controller facepack. Press the spring-loaded button and pull downward to remove. Insert the new A2C-WIFI …
The PSR-B was developed to provide a solution for irrigation controller and pump start relays installations that have insufficient power to energize the pump relay. A common cause for this problem is the use of too small a wire size for the distance from …
REL 2 is used to allow multiple controllers to operate the same low-voltage device (Master Valve or Pump Start Relay). IMPORTANT: REL 2 is NEVER connected to high voltage. It is for 24VAC devices, only. Diagrams listed below: … … … Two Controllers With …
The chattering you hear on a pump start relay is usually caused by insufficient amperage arriving at the relay from the controller. The first question you should ask yourself is – Did this Relay work for some time before or is this new installation? New …
This feature uses numbered day(s) of the month for watering instead of specific days of the week (odd days: 1st, 3rd, 5th, etc.; even days: 2nd, 4th, 6th, etc.) When you want to program ODD or EVEN days to water, press the (-) button until you see …
The Pro-C is compatible with the Hunter Solar Sync. Solar Sync is a sensor system that will automatically adjust the Pro-C controller’s watering run times (based on changes in local climate condition) by using the Seasonal Adjust function. The Solar Sync …
… Turn the dial to the Water Days position. The display will show the last program selected ( A , B , or C ). You can switch to another program by pressing the PRG button. The controller displays currently programmed active day schedule information. You …
This feature is convenient if you want to have a more consistent watering schedule without having to worry about the day of the week or the date. The interval you select is the amount of days between watering including the water day. Turn the dial to the …
Repeat steps 2 and 3 for each station. After entering the run time for the highest station number, press the button once to review the total run time programmed for all stations. … Pro-C - Setting Station Run …
Ensure you have a strong Wi-Fi signal. Wi-Fi coverage can be easily tested using a smartphone. A signal strength of two or three bars is recommended. Wi-Fi connectivity can also be tested on the HPC itself (signal strength is shown when you select a …
The rotor staking kit is designed to stabilize the shrub rotor while installed above ground. This rotor accessory is predominately used on slopes, either with the lateral pipe on the surface or slightly below the surface. Full installation details are …
A common reason for a controller to repeat a cycle is too many programmed start times. Only one start time per active program is required, a second start time will cycle the program an additional time. NOTE: In the Start Times dial position, the numbers …
Keep the Eco-Mat lightly moist at all times. Eco-Mat emitters flow at a rate of 0.6 gallons per hour (2.2 liters per hour). With consistent 14-inch (35-centimeter) laterals, the application rate will be 0.83 inches per hour (2.1 centimeters per hour). …
You can access reports for your controllers by selecting REPORTS at the bottom for the mobile version. Use the settings on the report tab to the right of the screen to change the following: Change the range of the report Clear all report data Refresh a …
Installing and maintaining an irrigation system is a complex task. That's why it's best to hire a qualified professional. Get connected with a local authorized landscape professional. Find A Contractor Hunter is dedicated to connecting our customers with …
With this option, you can select interval watering from 1 to 31 days. This feature is convenient if you want to have a more consistent watering schedule without having to worry about the day of the week or the date. The interval you select is the number …
When programming your NODE BT controller, you can change the NAME for each zone(station) to make it easier to identify the different areas of your landscape. … From the HOME dashboard, select the MORE tab on the lower right side of the screen. Select …