Residential & Commercial Irrigation
Residential & Commercial Irrigation
Push the button until the icon is displayed. All 4 digits will be displayed representing the year. Use the or buttons to change the year. Press the button to proceed to setting the month. All 4 digits will be displayed with the two digits on the …
The ACC controller can be reset, erasing some, or all programmed information. There are 5 different levels of reset command available. Once any of them is chosen, the information will be permanently erased. Turn the dial to the RUN Position. Press and …
The Pro-C is compatible with the Hunter Solar Sync. Solar Sync is a sensor system that will automatically adjust the Pro-C controller’s watering run times (based on changes in local climate condition) by using the Seasonal Adjust function. The Solar Sync …
NOTE: In the Start Times dial position, the numbers 1-4 do not represent stations. The numbers represent the program start times. Each program can start up to 4 times on the set days to water. One start time will activate all stations sequentially in that …
For drip irrigation systems using BTT, we recommend using regulation and filtration systems on all residential and commercial applications. Filters shall install directly on BTT's 3/4" hose thread outlet and connect to drip tubing providing regulated …
This is strongly discouraged by Hunter for the following reasons: It is unlikely that the pre-existing wire meets the specifications for gauge, twist, and solid copper. Pre-existing wire will not be color-coded correctly for the decoder wires. …
Controller power must be OFF when installing decoders in the two-wire path. Note: Decoder wire runs and connections must be completely waterproof. Decoder wiring is more critical than "conventional" 24 VAC solenoid wiring. Follow instructions closely! …
The chart below indicates the maximum wire runs that can be used when installing Hunter AC solenoid valves with controllers. The example in the chart below demonstrates the most commonly used wire size for station control and ground wire ( e.g.,12 AWG = …
Download the I-Core Owner’s Manual for detailed instructions on installation and programming an I-Core irrigation controller. … I-Core Owner's …
Download the DUAL Owner’s Manual for detailed instructions on how to install and program the two-wire decoder system for the I-Core irrigation controller. … DUAL Owner's …
The three sensors combined on this product are for wind speed, rainfall and temperature (near-freezing conditions). Each sensor operates independently of the other; therefore, any or all of them may be switching at a given moment. See the enclosed …
The standard MP Rotators have a matched precipitation rate of approximately 0.4 in/hr. This means any standard MP Rotator at any arc or radius can be placed on the same zone. The MP800SR can be configured to work well in head-to-head coverage in either …
Metal controllers will include a hole plug assembly in a pre-drilled factory hole on top of the controller. Remove the nut on the inside of the controller to remove the plug. Route the cable through the pre-drilled hole and the antenna nut. Then tighten …
After setting up an ACC2 or ICC2 controller in your Centralus account, you may choose to release the controller (serial number) to another user. This will require the controller's deletion. When the NEW user adds the controller into the Centralus …
When using Centralus Software, you have the ability to change your STATION , BLOCK , and/or DELAY RUN TIMES . There is a maximum run time of 12:00 hrs for all model A2C controllers. The minimum run time is 15 seconds for the decoder model and 1 …
Ensure you have a strong Wi-Fi signal. Wi-Fi coverage can be easily tested using a smartphone. A signal strength of two or three bars is recommended. Wi-Fi connectivity can also be tested on the HPC itself (signal strength is shown when you select a …
The rotor staking kit is designed to stabilize the shrub rotor while installed above ground. This rotor accessory is predominately used on slopes, either with the lateral pipe on the surface or slightly below the surface. Full installation details are …
When designing and installing irrigation systems, the water stream's trajectory and spray height leaving a sprinkler nozzle is important information. The chart below will show the total feet of height when using the largest nozzle for the ST-1600 model. …
This guide outlines the application, design, and installation of Hunter’s inline drip products that provide designers, installers, and irrigation managers a new class of irrigation technology. It is written for professionals who have a solid understanding …
The Automatic Flush Valve (AFV) allows debris to be flushed out of any dripline system. It is good practice to install an AFV at the end of any single dripline or grid of dripline. Flush the zone prior to use. An AFV may be used for any dripline system …
Similar to a sprinkler head, the Eco-Indicator pops up to provide visual indication that a drip system is operating. The Eco-Indicator has a highly visible yellow stem that pops up when the system is running at a pressure of least 12 PSI (0.8 bar; 83 …
Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … HEMT - Hunter Emitter Multi-Tool … Dripline …
The Roam XL Owner's Manual will guide you through the installation, wiring and operation of the Roam XL irrigation remote. … Roam XL Owner's …
The Roam Owner's Manual will guide you through the installation, wiring, and operation of the Roam irrigation remote. … Roam Owner's …