Residential & Commercial Irrigation
Residential & Commercial Irrigation
Sometimes the EC can retain an electrical glitch, and the result can be some programming anomalies such as the freezing of the AM/PM adjustment. Be sure the controllers programming dial is in the AUTOMATIC position before performing this reset procedure: …
Interval Watering is a feature that allows you to select the number of days to pass before the next watering day. For example, an interval of 3 will cycle the program once every three days and water on the third day. An interval of 1 is every day and an …
Hunter's EC controller comes with an Interval Watering feature. This Interval feature is set under the Water Days dial position on the controller. Interval Watering is a feature that allows you to select the number of days to pass before the next watering …
The WVP controller uses a numbered seven-day calendar to schedule the days to water. The display will show the days of the week as numbers 1–7. When programming the current time and day, you can select a number to represent the current day of the week. …
The SVC controller uses a numbered seven-day calendar to schedule the days to water. The display will show the days of the week as numbers 1–7. When programming the current time and day, you can select a number to represent the current day of the week. …
The EC controller uses a numbered seven-day calendar to schedule the days to water. The display will show the days of the week as numbers 1–7. When programming the current time and day, you can select a number to represent the current day of the week. The …
Before securing the controller to the wall, you must first remove the lower wiring compartment door. The door can easily be removed by following the simple steps below: Open the external door using the included key if outdoor version model. Indoor version …
The X-Core display shows the time and day when the controller is idle. The display changes when the dial is rotated to indicate the specific programming information to enter. When programming, the flashing portion of the display can be changed by pressing …
NOTE: In the Start Times dial position, the numbers 1-4 do not represent stations. The numbers represent the program start times. Each program can start up to 4 times on the set days to water. One start time will activate all stations sequentially in that …
X-Core Setting Days To Water …
To stop a station from running when the system cycles automatically, simply remove all station Run Times for station that you do not to operate. Make sure Programs A, B, C and on some controllers Program D, have a run time set to "0:00" for station that …
If your controller shows irrigation running (Flashing Sprinkler Icon), and your sprinklers are not working, you may have a wiring problem at the valves or the irrigation water supply has been shut down. If you have a master valve on your system (check for …
There are a number of reasons why the sprinklers may not come on from the automatic program. Assuming the controller will run the zones from the controller manually, you most likely have a programming issue. Below are a few possible causes to the …
This feature allows you to quickly diagnose wiring problems with your controller. Instead of having to check each field wiring circuit for potential problems, you can use the Hunter Quick Check circuit test procedure. To initiate the Quick Check test …
The X-Core is compatible with the Hunter Wireless Solar Sync. Solar Sync is a sensor system that will automatically adjust the X-Core controller’s watering run times (based on changes in local climate condition) by using the Seasonal Adjust function. The …
For accurate Solar Sync measurements, the controller needs to be programmed for the average peak season ET for your region. Use the following table for choosing your region. You can use methods A, B or C to help you choose which region is best for your …
If a Solar Sync sensor has been installed on the X-Core controller then the seasonal adjust value used by the controller will be calculated from the weather data supplied by the Solar Sync sensor. If it is decided that the Solar Sync sensor will no longer …
The X-Core controller will not water manually or automatically with the dial in the system off position. Valves currently watering will be shut off after the dial is turned to the system off position. The display will flash OFF for two seconds then …
The X-Core allows you to program a No Water Day(s). This feature is useful to inhibit watering on specific day(s). For example, if you always mow the lawn on Saturdays, you would designate Saturday as a No Water Day so that you are not mowing wet grass. …
Seasonal Adjustment is used to make global run time changes without re-programming the entire controller. To use the Seasonal Adjustment feature: NOTE: The controller should always be initially programmed in the 100% position. … To view the adjusted run …
After programming the X-Core, set the dial to the RUN position to enable automatic execution of all selected watering programs and start times. … X-Core - Automatic …
A Hunter weather sensor or other micro-switch type weather sensors can be connected to the Pro-C. The purpose of this sensor is to stop automatic watering when weather conditions dictate. Connecting a Hunter “Clik” Weather Sensor with a P2C Controller …
It's a combination drain hole and flush hole . It's a drain hole because we need to drain the water from below the nozzle turret so it doesn't push up on the nozzle turret in freezing climates. It’s a flush hole because when the head retracts, water and …
Using the PRB, the regulator in the body will take incoming pressures of 55-100 PSI and reduce them down to 45 PSI. This provides the optimum nozzle pressure to deliver the correct size droplets to the landscape for maximum water efficiency. Please …