Residential & Commercial Irrigation
Residential & Commercial Irrigation
The Flow-Clik Interface Box has a System Status indicator LED that provides information on the current status of the Flow-Clik system. RED indicates an unacceptable amount of water was flowing and the system has been shut down. (Water flow exceeded the …
If your sensor is not turning controller back on after a rain event, you may have debris in the spindle of the rain sensor. Remove the spindle assembly to check for debris or damage to the disks. … Pry upward on both sides of the middle stack of the …
The Flow-Clik monitors for a high flow condition, shutting down the system or individual zone when overflow occurs. Once the system has been shut off due to a high flow condition, the Flow-Clik turns the system back on automatically after a pre-selected …
When designing and installing irrigation systems, the water stream's trajectory and spray height leaving a sprinkler nozzle is important information. The chart below will show the total feet of height when using the largest nozzle for the ST-1600 model. …
The Automatic Flush Valve (AFV) allows debris to be flushed out of any dripline system. It is good practice to install an AFV at the end of any single dripline or grid of dripline. Flush the zone prior to use. An AFV may be used for any dripline system …
Similar to a sprinkler head, the Eco-Indicator pops up to provide visual indication that a drip system is operating. The Eco-Indicator has a highly visible yellow stem that pops up when the system is running at a pressure of least 12 PSI (0.8 bar; 83 …
HDL-PC & HDL-R - Emitter Line Maximum Length …
The Pro-C controller is supplied with a base 4-station module. The Pro-C is also compatible with the EZ Decoder System (EZDS) for hybrid conventional and two-wire operations. Add a Pro-C Decoder Module (PC-DM) to enable control for up to 32 total …
The Pro-C controller is supplied with a factory-installed base module for up to 4 stations on the PC-400 and up to 3 stations on the older PC-300. Additional modules may be added in increments of 3 stations (PCM-300) or a single 9-station (PCM-900) to …
With the Pro-C controller in production for 23 years, we have continuously upgraded to accommodate the innovative features. Below, you will find every panel we manufactured for the Pro-C model, including the wifi replacement front panel. For information …
REL 2 is used to allow multiple controllers to operate the same low-voltage device (Master Valve or Pump Start Relay). IMPORTANT: REL 2 is NEVER connected to high voltage. It is for 24VAC devices, only. Diagrams listed below: … … … Two Controllers With …
The chattering you hear on a pump start relay is usually caused by insufficient amperage arriving at the relay from the controller. The first question you should ask yourself is – Did this Relay work for some time before or is this new installation? New …
The rotor staking kit is designed to stabilize the shrub rotor while installed above ground. This rotor accessory is predominately used on slopes, either with the lateral pipe on the surface or slightly below the surface. Full installation details are …
Emitter tool for punching a pilot hole, inserting, and removing an emitter. … Emitter tool for punching pilot holes and pellets, inserting and removing an emitter, and cutting tubing. … Pocket Punch … HEMT - Hunter Emitter Multi-Tool … Emitter …
The NODE-BT controller offers an easy way to check the battery health of the actual controller without the use of a smartphone. Press the physical BATTERY CHECK BUTTON on NODE-BT controller and the battery indicator LED flashes green or red. 4 green …
Please select from the following choices to assist you with your Wireless Mini-Clik Sensor. Optional Quick Response® Technology - Immediate shutoff feature. Bypassing the Sensor - Turning the sensor off temporarily. Setting the Transmitter Address at …
Selecting Specific Days of the Week to Water For specific day of the week watering, the station number and 7 days of the week with a icon or a icon above the numbered day will be displayed. The icon would represent an "ON" watering day, while …
This feature permits the user to stop all programmed watering for a designated period from 1 to 7 days. At the end of the programmable rain off period, the controller will resume normal automatic operation. … Press the button until the System Off icon …
With the current time/day showing in the display press and hold the button to display the Manual Watering icon. The station number will also be displayed. Use the button to navigate to the station that you would like to manually activate. Use the or …
The system off function will turn your WVC controller off, stopping all automatic watering until turned back on with your WVP. … Use the button until the off icon is displayed. After flashing for a few seconds, the word “OFF” will appear in the display. …
Some of the features of the WVP include: Simple, push button programming Large Liquid Crystal Display (LCD) with easy to under- stand icons Radio communication WVC controllers up to 100 feet away Operates on standard 9-volt alkaline battery …
W e would prefer that you use a Hunter valve with a Hunter DC latching solenoid, but we realize that sometimes you may be retrofitting existing systems that have another manufacturer’s valves. We have done testing on the following solenoids and have found …
If you want to run separate stations (or zones) on different days, you would use 2 different programs. Hunter controllers have multiple programs (A, b, and C) and the ability for each program to have multiple start times. To set up each program, you …
You can access reports for your controllers by selecting REPORTS at the bottom for the mobile version. Use the settings on the report tab to the right of the screen to change the following: Change the range of the report Clear all report data Refresh a …