Residential & Commercial Irrigation
Residential & Commercial Irrigation
Every year, before the first freeze, the ritual of irrigation "blow out" becomes the priority for all irrigation systems that are in regions of the country where the frost level extends below the depth of the installed piping. Even if you have drained …
Pro-C - Setting the Current Date and Time …
Indoor Cabinet Route transformer cable through the hole on the bottom left side of the controller and connect one Yellow Wire to each of the screws marked AC and the Green Wire to GND . NOTE: This multi-voltage output transformer will read 15VAC & 9VAC on …
… Route valve wires between control valve location and controller. At valves, attach a common wire to either solenoid wire of all valves. This is most commonly a white colored wire. Attach a separate control wire to the remaining wire of each valve. All …
The chart below indicates the maximum wire runs that can be used when installing Hunter AC solenoid valves with controllers. The example in the chart below demonstrates the most commonly used wire size for station control and ground wire ( e.g.,12 AWG = …
Connect either wire from Master Valve to the P/MV terminal at the base of module. Connect remaining wire to the “COM” (Common) terminal. … Pro-C - Connecting a Master …
This feature permits the user to stop all programmed waterings for a designated period from 1 to 31 days. At the end of the programmable rain off period, the controller will resume normal automatic operation. Turn the dial to the SYSTEM OFF position. …
All necessary hardware is included for most installations. Use the hole at the top of the controller as a reference and secure a 1" (25 mm) screw into the wall. Note: Install screw anchors if attaching to drywall or masonry wall. Align controller with the …
Solar Sync Delay for Pro-C The delay feature is accessible only after the installation of the Solar Sync. The Solar Sync Delay feature allows the user to postpone seasonal adjustment changes from being made by Solar Sync for up to 99 days. While the Solar …
If a Solar Sync sensor has been installed on the Pro-C controller then the seasonal adjust value used by the controller will be calculated from the weather data supplied by the Solar Sync sensor. If it is decided that the Solar Sync sensor will no longer …
After Solar Sync has been installed and programmed, it is recommended to allow the system to run for a few days at the initial setting. Because of the variety in site conditions (including sensor location, amount of direct sunlight available to the …
You can also activate a program to water without using the dial. … With the dial in the RUN position, hold down the button for 2 seconds. This feature automatically defaults to program A. You can select program B, or C by pressing the PRG program. The …
The Pro-C is compatible with Hunter remote controls. The SmartPort wiring harness (included with all Hunter remotes) allows for fast and easy use of Hunter controls. Hunter remotes make it possible for you to operate the system without having to walk back …
If want to clear the memory on your controller and start from fresh or if your controller is not responding to your commands, you can reset the Pro-C. … Press and hold the program button. Press and release and the RESET button on the back of the …
Easy Retrieve allows the user to save a program in the controller's memory for later use. The saved program can be retrieved at any time to overwrite unwanted changes in the current program. The saved program can then be used as a custom default …
The Pro-C allows the user a simplified method for running a test program. This feature operates each station in numerical sequence, from the lowest to the highest. You can start with any station. This is a great feature to check the operation of your …
This feature uses numbered day(s) of the month for watering instead of specific days of the week (odd days: 1st, 3rd, 5th, etc.; even days: 2nd, 4th, 6th, etc.) When you want to program ODD or EVEN days to water, press the (-) button until you see …
The Pro-C is capable of operating three separate lighting transformers equipped with the PXSYNC interface box. You can also operate the FX LX lighting transformer via the Pro-C controller using the LX external inputs. When using the Pro-C to operate …
This feature allows the user to insert a delay between when one station turns off and the next station turns on. This is very helpful on systems with slow closing valves or on pump systems that are operating near maximum flow or have slow well recovery. … …
This feature is convenient if you want to have a more consistent watering schedule without having to worry about the day of the week or the date. The interval you select is the amount of days between watering including the water day. Turn the dial to the …
This circuit diagnostic procedure is can quickly identify shorts; commonly caused by faulty solenoids or when a bare common wire touches a bare station control wire. To initiate the Hunter Quick Check test procedure: Press the , , and buttons …
The Pro-C is factory configured with 3 independent programs (A , B , C with four start times each) for different plant type requirements. The Pro-C can be customized to display only the required programs. You can hide those programs that are not required …
The Pro-C allows the user to program the controller so that the sensor disables watering on only desired stations. For example, patio gardens that have pots under overhangs and roofs may not receive water when it rains and will continue to need to be …
Cycle and Soak The Cycle and Soak feature allows you to split a station’s run time into more usable, shorter watering durations. This feature is useful when applying water to slopes and tight soils because it automatically applies water more slowly, …